Appointment

 

 

Presented here down the page you can discover lots of amazing material around Installing A Bathtub.

Installing a bathtub isn't precisely rocket science, however it does require strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open a wall surface to remove the old bathtub and position the brand-new tub, the task is much harder. In either instance, the job is within a residence handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually qualified on your own for the task and also are comfortable trying it. Rather than employing a professional to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will help you install a brand-new bath tub in your restroom if you have currently bought a new bathtub and don't require to change the plan of your previous water pipelines.
Your tools as well as material checklist need to make up the following:

 

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipeline Caps


 

Preparing for the Setup

First of all, the supporting structure supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is essential to ensure that if the faucet includes a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the taps device to avoid strain on the bathtub.
Fit the versatile faucet ports to the bottom of both faucets utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now prepare to be suited its final setting.

 

 

Removing Old Touches

If you require to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be fairly problematic because of the limited accessibility that is frequently the case.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipes. When the supply pipelines have actually been eliminated, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.

 

 

Mounting the Bath tub

Making use of the two wood boards under its feet, position the tub in the required position. The wooden boards are useful in uniformly spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the bathtub until the level reviews level.
To mount faucets, fit the bottom of the outermost adaptable faucet port to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the supply of water as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bath tub as well as likewise check the overflow outlet and the regular electrical outlet for leaks.
Lastly, deal with the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the bathtub ought to wait up until the bath tub has been made use of at the very least once as this will resolve it into its final setting.

 

 

Fitting New Taps

If the tails of the new taps are plastic, then you will require a plastic connector to stop damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the mounting hole in the bath/basin guaranteeing that the washers are in place in between the tap and the sink. Secure the tap in place with the maker supplied backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Tiling Around the Bath tub

In the location where the bathroom fulfills the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to fracture an inflexible seal, creating the water to pass through the wall surface in between the bath as well as the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and also can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can fracture relatively early if you do not think about this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is recommended to fit the ceramic tiles using water-resistant or water resistant adhesive and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I stumbled upon that article about A Step-by-Step Guide to Installing a Bathtub while perusing the internet. In case you appreciated our blog posting kindly do not forget to share it. We thank you for reading our article about How to Install a Bathtub.

Visit My Website